Zone HVAC Groups

Workspace:  Systems/ ZoneHVAC Groups/Create-Edit  and Systems/ ZoneHVAC Groups/Diagram

Workspace Area Links

 

To set Zone HVAC Groups for a BEM the user will need to complete a few steps within the Credit/Edit workspace.  The user may not need to go to the Diagrams Workspace.  If the user selects a template and they do not need to edit the Zone HVAC template by either changing a component, editing the component properties or utilizing other features in the Diagram Workspace.  The features within  each workspace are described in greater detail below as well as the steps involved in a typical workflow.

 

When a user has assigned a thermal zone to a Zone HVAC Group, the letters (HG) will appear at the end of the thermal zone listing on the Project Tree.

Create/Edit Workspace

The main workspace areas are described here.

 

Key Workflow Steps

For each BEM a user must setup at least one Zone HVAC Group that contains thermal zones.  One approach to setting up the Zone HVAC Groups is:

  1. The user should consider how they would like to set up Zone HVAC Groups for the model.  How many different Zone HVAC Groups should there be?  What thermal zones should be included?  Tip: The user can add and edit Zone HVAC Groups to the model at any time, however it is easier to accomplish and manage this at the beginning of the process.  
  2. Create/Edit Table - Select New to create the desired number of Zone HVAC Groups
  3. Select the desired thermal zones for each Zone HVAC Group (multiple thermal zones can be selected by using the shift key to select a continuous range or the CTRL key to select multiple in different locations), and Drag and Drop them on the desired Zone HVAC Group (Name Column).  The outcome will be a list of the thermal zones displayed beneath the Zone HVAC Group.
  4. Select a Template for each Zone HVAC Group - the user can select a template from the drop down list, which contains the Zone HVAC Groups that have been previously set up within that Library; they can change the Source Library to access and select other Zone HVAC Group Templates; or the user can go to the Templates/Zone HVAC Group and create and/or edit existing to create their own template
  5. Assign Components to Surfaces (optional)
  6. Go to Diagram Workspace to edit any of the Zone HVAC Templates (optional)
  7. Set Heating and Cooling Priorities for Air Terminals and other zone equipment in the Zone HVAC Group Controls table (optional)
  8. Select Validate to validate the Zone HVAC Group and identify if there are any issues with the current set up.

 

Zone HVAC Groups Create/Edit Table

New

Creates a new Zone HVAC Group and a new row in the table

Delete

The selected row is deleted along with the ZoneHVAC Group and the previous information that had been assigned to it.

Name

A default name is assigned in sequential order starting with Zone HVAC Group-1, which can be changed by the user

Assign Thermal Zones to Zone HVAC Group

Users can assign thermal zones to Zone HVAC Groups by highlighting individual thermal zones and/or multiple thermal zones (holding down CTRL key) in the Active Project Model Tree and then drag and drop them to the desired Zone HVAC Group.  After completing the 'drag and drop' the names of the thermal zones will appear in the rows below the Zone HVAC Group.

Template

The user can select a Zone HVAC Group Template from the drop down list to associate with the Zone HVAC Group and to establish what will be the demand side for the Air Loop.  The selections available depend on what is available in the Source Library.  The user can create Zone HVAC Groups Templates in the Templates Workspace.

Assign

Allows the user to assign the energy contribution of Zone HVAC equipment to surfaces in the BEM.

 

Zone HVAC Groups Controls Table

Once a template has been selected the diagram for the Zone HVAC Group is displayed in the 2d view and the Air Terminals and other Zone Equipment that are included in the Zone HVAC Group are automatically displayed in the first column.  In the example below the Air Terminal, a VAV with reheat (VAVR-1), is included in the table as well as the Four Pipe Fan Coil (FPFC-1), which is displayed under Zone Equipment.

 

Heating Priority

If more than one type of equipment (including both Air Terminals and Zone Equipment) is included within a Zone HVAC Group the user is required to establish the heating priority for that equipment set.  Each cell in the column contains a drop down list that allows the user to select the priority for the specific equipment.  Different types of equipment cannot have the same priority number.  In the example below we tried to set the VAV to heating priority 1 in addition to the four pipe fan coil unit, and we received an error message notification.  If we wanted to change the order we could select FPFC-1 and change to either blank (0) or select a lower number.  Then we could change the VAVR-1 to a 1 priority.

 

Cooling Priority

If more than one type of equipment (including both Air Terminals and Zone Equipment) is included within a Zone HVAC Group the user is required to establish the cooling priority for that equipment set.  Each cell in the column contains a drop down list that allows the user to select the priority for the specific equipment.  Different types of equipment cannot have the same priority number.

 

Validation Table

If the user selects Validate and there are issues with the Zone HVAC Group set up, the Validation tab will be come to the front and the issues will be displayed in a table format.  If there are no issues related to the Validation Rule Set, the user will receive the message "Validation run successful and did not find any errors with your system configuration".

Diagram Workspace

The main workspace areas are described here.

 

Key Workflow Tasks

If the user has gone to the Diagram workspace there any of a number of things they could potentially interested in doing that don't require a specific order.  Some of the common tasks with links to detailed descriptions include:

Adding equipment to the Zone HVAC Group (drag and drop from stencil)

The user can select shapes from the Zone HVAC stencil and then drag and drop the component shapes onto the Zone HVAC Group 2d canvas.  For Air terminals they will most likely need to draw or edit connectors.

Adding controls to the Zone HVAC Group (drag and drop from stencil)

The user can select shapes from the Zone HVAC Controls Sensors Stencil and then drag and drop the controls component shapes onto the Zone HVAC Group 2d canvas.  For Controllers  users will most likely need to draw or edit connectors.

Changing Equipment Sub Types (drop down list in component information area)

The user needs to select the desired component shape in the 2d view and then go to the Component Information properties and select a different Sub Type from the drop down list.

Selecting a Library Entity for each piece of equipment (required to run a simulation)

The user needs to select the desired component shape in the 2d view and then go to the Component Information properties and select a Library Entity from the drop down list.  The user can also change the Source Library to access other Library Entity options from different Source Libraries.

Selecting a Water Loop to connect to (relevant components)

The user needs to select the desired component shape in the 2d view and then go to the Component Information properties and select a water loop type from the drop down list.  

Reconfiguring the Zone HVAC Group diagram

The Zone HVAC Groups can be reconfigured in a number of ways using the Zone HVAC Group 2d canvas tools.

Changing Heating and Cooling Priorities

If more than one type of equipment (including both Air Terminals and Zone Equipment) is included within a Zone HVAC Group the user is required to establish the heating and cooling priority separately for that equipment set.  Each cell in the column contains a drop down list that allows the user to select the priority for the specific equipment.  Different types of equipment cannot have the same priority number.

Trying to rectify validation issues that have been identified.

 

 

 

 

______________________________________________________________________________________

© Copyright 2013 Simergy, Sustainable IQ, Inc.